How To Repair & Replace The iPhone X Back Glass?
The most daunting feature of the iPhone X is its back glass. Everyone drooled over its elegance when this first came out. Yet we knew it would be a delicate phone compared to prior steel-back iPhone models like iPhone 7 and 7Plus. Therefore, you should be extra careful about your iPhone X. If it’s broken, you’d be surprised to learn that the most expensive smartphones on the market also have the highest place glass repair costs. Anyhow have you got your iPhone back glass broken? With just a few simple tools and a little know-how, your phone will look as good as new. This blog post will teach you how to repair your iPhone X back glass panel. The iPhone X back glass can be fixed in a variety of ways.
Repair iPhone back glass by Laser Separation Technique
Though the Laser separation technique is more expensive than the traditional methods of removing a broken iPhone glass. The laser machine has many incredible benefits; it can remove glass easily and quickly. It can separate the mid-frames and back glasses of iPhones and many other smartphones. Here’s how this procedure works:
Automated center calibration:
Firstly, Place the phone on the focus area, then spin the black wheel. It has an automated focal length tester. The blue light will begin to twinkle as soon as it is focused at the ideal distance.
Place the phone on the location mold, which uses patented technology. It can automatically calibrate the center and is quick and accurate. The margin of error is less than 0.002mm.
Start laser separating:
The next step is to use the computer to locate the drawing of the iPhone X/XS/XS MAX once the position has been determined. Then press “Mark” to begin the laser separation. The machine will laser twice to separate the back glass here. Make sure that the drawings are accurate.
Remove glass and clean glue:
After the laser work is completed, successfully remove the iPhone XS back glass with a blade, a pry piece, and pliers quickly.
After removing the glass, use the laser machine to remove any remaining glue. Removing the residual adhesive can be difficult if you don’t have a laser machine, but a hair dryer or heat gun can help.
Set up new glass:
Using a glue gun, apply glue to the back frame. It is preferable to add glue without imposing rules. Finally, replace the glass.
How to replace iPhone X back glass
If the damage to the back glass is severe, it needs a replacement. Here’s how you can replace the back glass of the iPhone X or any other iPhone.
Tools Required to replace iPhone X Back Glass
Before repairing your phone, the first thing to do is to gear up with the best essential tools. Here is the list of necessary tools you will need to repair the iPhone X back glass:
- A heat gun
- For storing screws
- Tool for opening iFlex
- Tweezers
- Take Set
- Tool for plastic prying
- PL1 Pentalobe screwdriver
- PH00 Phillips screwdriver
- Y-style Y000 screwdriver
Now that you are all geared up with the tools, here is the most comprehensive step-by-step guide to reviving your iPhone X back glass.
Step 1: Switch off your iPhone X
Please turn the phone off to prevent any harm during repairs. Press the standby button and one of the two-volume buttons for around three seconds to accomplish this. Swipe the “Power Off” slider from left to right when it displays on the screen. Within 10 seconds, your iPhone will shut off.
Step 2: Removing the screws from the rear case
It would be best if you had a pentalobe screwdriver (PL1) to open your iPhone X. The two pentalobe screws to the right and left of the Lightning connector should be removed and stored in a screw container.
Step 3: Remove the display
It would be best if you heated the glue to remove the display because it is firmly attached to the remainder of the case. Set it down on a smooth, clean surface to prevent scratching the back of your iPhone X when lifting the display. Now run a hot air tool evenly over the display’s adhesive edge, like a hot air drier or a standard hair dryer.
To make a small space between the stainless steel and display frame, position the suction cup on the device’s bottom edge and pull it upward.
To widen the tiny space, insert a solid, flat tool. Use the tool and flat plastic picks to press the display just a little bit upward simultaneously.
To remove the stuck display from your iPhone, move the tool around the device’s frame one step at a time. Continue pushing upward with the plectrum until the noses separate from the stainless steel frame.
Step 4: Opening the display
Using a soft plastic plectrum, gently push the display upward from the aluminum frame. The display can be folded up to the standby button’s side once entirely disconnected. To keep it standing vertically, lean it against a solid surface.
Step 5: Disconnecting the battery
Always remember to unplug the battery connector before beginning the repair to prevent a possible short circuit. Keep in mind that the length of the screws used in the iPhone X varies.
Use a Y-type screwdriver to remove the cover plate by unscrewing the Y-type screws. Using a flat plastic tool, carefully slide the battery connector under the connector.
Step 6: Disconnecting the display connector
Three connectors link the display to the rest of the iPhone X.
Carefully remove each connector from the logic board using a spudger. Make sure that the flex wire for the earpiece is slightly stuck to the top of the display. You can entirely remove the monitor once all connectors have been unplugged.
Step 7: Removing the bracket plate
Remove the speaker’s mounting plate by removing the Y-Type and Phillips screws. Open the plate up, then use a spudger to pry the connector apart. Finally, you can take off the bracket plate.
Step 8: Detach the speaker
Remove the cover plate by removing the Y-type screw from the bracket plate. Lift the flex cable and unplug the speaker connector. Lift the tightly bound speaker with the spudger and gently pry it off. You can take the speaker and flex wire out of your computer once the speaker has been loosened.
Step 9: Removing the Taptic Engine
The Phillips screws holding the Taptic Engine in place must first be removed. Utilizing a spudger, carefully unplug the Taptic Engine’s connector. With tweezers, carefully remove the Taptic Engine from your iPhone.
Step 10: Remove the battery
Pull out by the four tabs securing the iPhone X battery to the cover. The battery’s bottom edge has three tabs taped to it, while the top edge has one. Remove the black tabs with a spatula or tweezers. Underneath are the white sticky strips. Use a wide, strong instrument to carefully lever the battery out without bending it if one of the tapes tears. For this, a battery spudger is employed.
You can easily remove the battery from the device once all the sticky strips have been eliminated.
Step 11: Removing the camera
First, remove the two Phillips screws holding the iSight camera bracket plate. Lift the little eyelet holding the bracket plate on the upper edge of the rear casing. Use a spudger to detach the iSight camera’s two connectors from the logic board. With the spudger, carefully pry the camera out of its lead and set it aside.
Step 12: Unfasten the sim card tray & logic board
The SIM card tray must be removed before removing the logic board. To remove the SIM card tray, insert a paperclip or a SIM tool into the gap next to the tray.
Carefully detach all connectors from the logic board using a spudger. This contains the volume controls, flash, FaceTime camera, and Lightning connector. Under the flex cable of the FaceTime camera is a connection. To remove the connector, carefully bend the cable to one side.
After removing all screws and connectors, carefully bend the flex wires to one side and remove the logic board.
Step 13: Separate barometric vent
A little plastic cover that is fastened on now covers the location of the headphone jack in earlier models. With tweezers, unfasten the screw and remove the plastic cover.
With the aid of a specialized screwdriver, the Standoff screws can be removed. However, using a thin, appropriate slotted screwdriver is also an option.
Step 14: Removing the lightning connector
Your iPhone X rear case has the Lightning connector’s flexible cable. The Lightning connector is also secured with several screws. Remove all of the Lightning connector’s screws. Two screws require more effort to remove because they are significantly longer.
To make removing it simpler, warm up the entire flex cable with a hot air source. Additionally, pry the Lightning connector out of its lead at the edge of the back casing.
Step 15: Pull out the antenna flex cable
The bottom edge of the back cover is where the antenna cable for the speaker is fastened. It joins the logic board and speaker. Use a heat gun or hair drier to warm the glued flex cable evenly. Using a steel spatula, remove the cable out of the back cover one at a time.
Step 16: Removing true depth camera
Together with the infrared sensor and Face ID, the TrueDepth camera makes up a single device. On both sides, it is linked to the back casing. The bottom of the back cover is where the integrated flex cable is glued.
Carefully detach the TrueDepth camera and Face ID device using tweezers.
Use a steel spatula to gradually loosen the glued flex cable with heat until you can remove the complete unit from your iPhone.
Step 17: Separate cable set of standby button and flashlight
A common flex cable connects the flash and the standby button.
First, remove the screws holding the standby button in place.
Using tweezers and a steel spatula, carefully remove the heated flex cable from the bottom of the back cover.
Finally, use a lever to release the lead on the microphone adjacent to the flashlight.
Check if the microphone’s flex cable and sticky surface have come loose. Remove it from the rear cover if it is there and attach it to the proper spot on the flex cable.
Step 18: Removing wifi flex cable
The wifi antenna cable is fastened with numerous screws in addition to being bonded in the upper portion of the iPhone X back case. Small metal clamps are concurrently fixed in the rear case by a few.
Remove all of the screws holding the clamp in place first.
Using a steel spatula and heat, carefully remove the flex cable set from the back cover. Afterward, remove the entire cable set.
Step 19: Take out the Bluetooth flex cable.
The back cover must also be removed to access the Bluetooth antenna line. This is situated directly next to the iSight camera’s lead.
The Phillips screw must first be removed.
Then, using heat and a steel spatula, gradually loosen the flex cable until you can remove it.
Step 20: Removing the display bracket
Before removing the staples, keep in mind their orientation. The display won’t sit appropriately if they are put improperly. By releasing all Phillips screws, you can detach the display clamps from the back cover’s edge.
Step 20: Detach the volume control cable
The cable set is glued, and the buttons are screwed into the back casing.
First, remove all Phillips screws from the edge of the back cover.
Before carefully extracting it from the bottom of the back cover with a steel spatula, heat the entire cable set with hot air. Heat the cable multiple times if necessary.
Step 21: Extract the standby and volume buttons
With tweezers, carefully detach the standby button’s metal bracket on one side and then completely pull it out.
To remove the standby button’s thread, lever the silver metal clamp upward from one side and pull it up.
Now press the standby button on your iPhone X’s back case frame from the inside out. Use the volume buttons in the same manner.
Step 22: Prepare a new back cover.
There are no longer any components. Compare your spare back cover to the previous one before you start assembling your iPhone X to see if any small components, like brackets or seals, need to be replaced. Place the two rear covers side by side and replace any missing pieces.
Step 23: Installing standby and volume buttons
Reinstall the standby button in the notch on the edge of the back case. To make the metal clamp secure on the standby button’s thread, push it vertically onto the button’s thread. The clamp should then be pressed until the other side locks.
Finally, attach the metal bracket to the clamp by hooking it to one side and then to the other.
For the volume buttons, use the same steps.
Step 24: Fix the volume control cable
The cable set of volume buttons, mute buttons, and charging coil should then be attached.
Place the charging coil in the back cover’s original location first.
Place the volume buttons’ metal clamps along the edge of the back casing. You can use the Phillips screws to secure the cable set once everything is properly aligned.
Now firmly press the charging coil and thin flex cable against the back cover. After this, insert the display bracket.
Step 25: Fit the Bluetooth flex cable
Reattach the short Bluetooth antenna wire to the iSight camera’s guide.
Step 26: Installing wifi flex cable
Replace the flex cable in its original location. Attach the flex cable to the back cover while screwing on the clamps simultaneously. After this, Install the antenna flex cable and put it in the lightning connector.
Step 27: Installing the biometric vent
The barometer vent should be installed and secured at the bottom edge of the rear case. After this, fix the logic board, install the sim card tray, and Reinstall the iSight camera.
Step 28: Prepare the replacement battery.
Ensure the protective films are pointing in the correct direction before inserting the adhesive strips into the device. Remove the thick blue protective film, then attach the adhesive strips to the battery’s bottom.
Leave space for folding over the tabs on both sides before affixing the adhesive strips.
Fold the tabs and glue them to the battery’s edges after flipping them over. Now, separate the adhesive strips from the sizable pink protection film.
Step 29: Inserting the battery
Reinstall the battery in the back casing and firmly press it in place. Make sure the battery is in the right place. Utilize the connection as a guide since it must precisely fit on the contact on the logic board. After this, attach the display.
Step 30: Attach the new adhesive frame
Pull the protective sheet from the underside of the adhesive frame after properly aligning it. Starting with just one edge of the frame, place the sticky frame and push it firmly as you go. In addition, use the plastic spudger to press it down and make the frame as smooth as possible.
The central section of the protective film should then be removed.
Finally, please remove the last protective film from the housing’s edge, leaving only a clear adhesive film in its place. Finally, connect the display.
Step 31: Installing the display
Fold the display over slowly while holding it with both hands. One by one, press them down along the frame. Before applying glue, test your iPhone’s display and other features.
Step 32: Fixing up the new glass and back cover screws.
Finally, tighten the two pentalobe screws to the left and right of the Lightning connector.
Conclusion:
Thanks for reading the guide on repairing an iPhone X back glass. We hope that it has been helpful and that you feel confident tackling the task yourself. Moreover, If you are looking for mobile repair shop management software you may check out RepairBuddy WordPress Plugin. If you have any questions, ask a professional for help. Good luck!
